start:hype_file_reference:geodata.txt
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
start:hype_file_reference:geodata.txt [2020/04/28 11:28] cpers |
start:hype_file_reference:geodata.txt [2020/04/30 07:25] cpers |
||
|---|---|---|---|
| Line 40: | Line 40: | ||
| | ''ilregion'' | //-// | optional | lake region for ilake parameters, integer > 0, default is 1 | | | ''ilregion'' | //-// | optional | lake region for ilake parameters, integer > 0, default is 1 | | ||
| | ''olregion'' | //-// | optional | lake region for olake parameters, integer > 0, default is 1 | | | ''olregion'' | //-// | optional | lake region for olake parameters, integer > 0, default is 1 | | ||
| - | | ''elev_mean'' | //m// | optional | mean elevation of sub-basin | | + | | ''elev_mean'' | //m// | optional | mean elevation of subbasin | |
| | ''elev_std'' | //m// | optional | variation (standard deviation) in elevation in a subbasin | | | ''elev_std'' | //m// | optional | variation (standard deviation) in elevation in a subbasin | | ||
| | ''slope_mean'' | //%// | optional/mandatory | slope (>= 0%), mandatory for nutrient modelling | | | ''slope_mean'' | //%// | optional/mandatory | slope (>= 0%), mandatory for nutrient modelling | | ||
| | ''slope_std'' | //%// | optional | variation (standard deviation) of slope in a subbasin | | | ''slope_std'' | //%// | optional | variation (standard deviation) of slope in a subbasin | | ||
| | ''lake_depth'' | //m// | optional | water depth from outflow threshold, below which outlet flow ceases, down to mean depth for outlet lake, used for general lake discharge curve. Can also be defined in [[start:hype_file_reference:lakedata.txt|LakeData.txt]] or [[start:hype_file_reference:par.txt|par.txt]]. Definition in LakeData takes precedence. Must be > 0, or set to -9999 to use general or region parameter value from par.txt. | | | ''lake_depth'' | //m// | optional | water depth from outflow threshold, below which outlet flow ceases, down to mean depth for outlet lake, used for general lake discharge curve. Can also be defined in [[start:hype_file_reference:lakedata.txt|LakeData.txt]] or [[start:hype_file_reference:par.txt|par.txt]]. Definition in LakeData takes precedence. Must be > 0, or set to -9999 to use general or region parameter value from par.txt. | | ||
| - | | ''lakedataid'' | //-// | optional | lake or lake basin ID, coupled to //lakedataid// in [[start:hype_file_reference:lakedata.txt|LakeData.txt]], 0 if no such coupling exists | | + | | ''lakedataid'' | //-// | optional | olake ID, coupled to //lakedataid// in [[start:hype_file_reference:lakedata.txt|LakeData.txt]], 0 if no such coupling exists | |
| | ''icatch'' | //-// | optional | fraction of local runoff that goes through the local lake (ilake), the rests runs directly into the main watercourse. To instead use parameter values (''gicatch'', ''ilicatch'' in [[start:hype_file_reference:par.txt|par.txt]]) for a single simulation set value to -9999 in GeoData or remove the column completely. | | | ''icatch'' | //-// | optional | fraction of local runoff that goes through the local lake (ilake), the rests runs directly into the main watercourse. To instead use parameter values (''gicatch'', ''ilicatch'' in [[start:hype_file_reference:par.txt|par.txt]]) for a single simulation set value to -9999 in GeoData or remove the column completely. | | ||
| | ''rivlen'' | //m// | mandatory | length of main watercourse within subbasin | | | ''rivlen'' | //m// | mandatory | length of main watercourse within subbasin | | ||
start/hype_file_reference/geodata.txt.txt ยท Last modified: 2024/02/15 09:44 by cpers
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
