start:hype_tutorials:transfer_atmdep
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
start:hype_tutorials:transfer_atmdep [2022/01/27 11:17] cpers |
start:hype_tutorials:transfer_atmdep [2024/01/25 11:37] (current) |
||
|---|---|---|---|
| Line 6: | Line 6: | ||
| ^ parameter ^ unit of parameter ^ description ^ replacement procedure ^ | ^ parameter ^ unit of parameter ^ description ^ replacement procedure ^ | ||
| - | |drydeppp | kg km-2 d-1 | dry deposition of PP | Replace with columns PP_DD_L1..PP_DD_Ln, where n is the number of land uses in the model. Set the same value for all subbasins. The same unit is used for a model with daily time step, because the unit of the file is kg km-2 ts-1.| | + | |drydeppp | //kg/(km<sup>2</sup> d)// | dry deposition of PP | Replace with columns PP_DD_L1..PP_DD_Ln, where n is the number of land uses in the model. Set the same value for all subbasins. The same unit is used for a model with daily time step, because the unit of the file is //kg/(km<sup>2</sup> ts)//.| |
| - | |wetdepsp | µg L-1 |wet deposition of SP| Replace with column SP_WD, The unit of the file is mg/L so multiply the value of the par file with 1000. Set the same value for all subbasins.| | + | |wetdepsp | //μg/l// |wet deposition of SP| Replace with column SP_WD, The unit of the file is //mg/l// so multiply the value of the par file with 1000. Set the same value for all subbasins.| |
| - | |wetdepspl |kg km-2 d-1 |wet deposition load of SP on water surfaces| Replace with dry deposition in AtmdepData.txt, because it is defined as load. Set column SP_DD_V3 with the same value for all subbasins. The load will be applied on V3, i.e. vegetation type 3 (water surfaces).| | + | |wetdepspl |//kg/(km<sup>2</sup> d)// |wet deposition load of SP on water surfaces| Replace with dry deposition in AtmdepData.txt, because it is defined as load. Set column SP_DD_V3 with the same value for all subbasins. The load will be applied on V3, i.e. vegetation type 3 (water surfaces).| |
| In GeoData.txt nitrogen deposition was given by subbasin and vegetation type and/or month. They can be tranfered to the new file like this: | In GeoData.txt nitrogen deposition was given by subbasin and vegetation type and/or month. They can be tranfered to the new file like this: | ||
| ^ column ^ unit of geodata variable ^ description ^ replacement procedure ^ | ^ column ^ unit of geodata variable ^ description ^ replacement procedure ^ | ||
| - | | wetdep_n | ug/L | wet deposition of inorganic nitrogen (IN), concentration of precipitation | Replaced by column IN_WD in AtmdepData.txt. Note the unit change to mg/L in the new file.| | + | | wetdep_n | //μg/l// | wet deposition of inorganic nitrogen (IN), concentration of precipitation | Replaced by column IN_WD in AtmdepData.txt. Note the unit change to //mg/l// in the new file.| |
| - | |drydep_n1 | kg/km2/d | dry deposition of inorganic nitrogen on vegetation type 1 (open) | Replaced by column IN_DD_V1 in AtmdepData.txt. The same unit is used for a model with daily time step, because the unit of the file is kg km-2 ts-1. The load will be applied on V1, i.e. vegetation type 1 (open land).| | + | |drydep_n1 | //kg/(km<sup>2</sup> d)// | dry deposition of inorganic nitrogen on vegetation type 1 (open) | Replaced by column IN_DD_V1 in AtmdepData.txt. The same unit is used for a model with daily time step, because the unit of the file is kg km-2 ts-1. The load will be applied on V1, i.e. vegetation type 1 (open land).| |
| - | |drydep_n2 | kg/km2/d | dry deposition of inorganic nitrogen on vegetation type 2 (forest) | Replaced by column IN_DD_V2 in AtmdepData.txt.| | + | |drydep_n2 | //kg/(km<sup>2</sup> d)// | dry deposition of inorganic nitrogen on vegetation type 2 (forest) | Replaced by column IN_DD_V2 in AtmdepData.txt.| |
| - | |drydep_n3 | kg/km2/d | dry deposition of inorganic nitrogen on vegetation type 3 (water) | Replaced by column IN_DD_V3 in AtmdepData.txt.| | + | |drydep_n3 | //kg/(km<sup>2</sup> d)// | dry deposition of inorganic nitrogen on vegetation type 3 (water) | Replaced by column IN_DD_V3 in AtmdepData.txt.| |
| - | |deploadn1-deploadn12 | kg/km2/d | total deposition of inorganic nitrogen on water, January - December | Replaced by adding as dry deposition of IN in AtmdepData.txt. Set columns IN_DD_M1_V3 ... IN_DD_M12_V3. The load will be applied on V3 (water), with different values for each month M1..M12.| | + | |deploadn1-deploadn12 | //kg/(km<sup>2</sup> d)// | total deposition of inorganic nitrogen on water, January - December | Replaced by adding as dry deposition of IN in AtmdepData.txt. Set columns IN_DD_M1_V3 ... IN_DD_M12_V3. The load will be applied on V3 (water), with different values for each month M1..M12.| |
start/hype_tutorials/transfer_atmdep.1643278628.txt.gz · Last modified: 2023/11/16 14:28 (external edit)
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
